import 'dart:typed_data';
import 'package:flutter_test/flutter_test.dart';
import 'package:hvbt_dash/core/protocol/neg8.dart';
import 'package:hvbt_dash/core/protocol/s300_parser.dart';
import 'package:hvbt_dash/core/protocol/temp_table.dart';

/// Builds a zeroed 128-byte S300 frame and stamps the NEG8 checksum at byte 127.
Uint8List _buildS300Frame({
  int rpm = 0,
  int vss = 0,
  int mapRaw = 0,
  int tps = 0,
  int inj = 0,
  int ign = 0,
  int ect = 0x80, // tempXlt[0x80]=73 → 73-40=33°C
  int iat = 0x80,
  int bat = 0,
  int sw1 = 0,
  int sw2 = 0,
  int sw3 = 0,
  int krtrd = 0,
  int gear = 0,
}) {
  final frame = Uint8List(128);
  // Header
  frame[0] = 0x1B;
  frame[1] = 0x00;
  // RPM: bytes +3..4, little-endian, raw
  frame[3] = rpm & 0xFF;
  frame[4] = (rpm >> 8) & 0xFF;
  // VSS: bytes +5..6, little-endian
  frame[5] = vss & 0xFF;
  frame[6] = (vss >> 8) & 0xFF;
  // MAP: bytes +7..8, little-endian
  frame[7] = mapRaw & 0xFF;
  frame[8] = (mapRaw >> 8) & 0xFF;
  // TPS: byte +9
  frame[9] = tps;
  // INJ: bytes +10..11, BE
  frame[10] = (inj >> 8) & 0xFF;
  frame[11] = inj & 0xFF;
  // IGN: byte +12
  frame[12] = ign;
  // KRtrd: byte +13
  frame[13] = krtrd;
  // SW bitmaps
  frame[0x11] = sw1;
  frame[0x12] = sw2;
  frame[0x13] = sw3;
  // Gear: decimal offset 27
  frame[27] = gear;
  // ECT: decimal offset 33
  frame[33] = ect;
  // IAT: decimal offset 34
  frame[34] = iat;
  // BAT: decimal offset 36
  frame[36] = bat;

  // Stamp NEG8 checksum at byte 127
  int neg8 = 0;
  for (int i = 0; i < 127; i++) {
    neg8 = (neg8 - frame[i]) & 0xFF;
  }
  frame[127] = neg8;
  return frame;
}

void main() {
  group('S300 parser', () {
    test('parses RPM correctly', () {
      // RPM raw = 3000
      final frame = _buildS300Frame(rpm: 3000);
      final state = parseS300(frame);
      expect(state.rpm, equals(3000.0));
    });

    test('parses VSS = 0 when raw < 893', () {
      final frame = _buildS300Frame(vss: 500);
      final state = parseS300(frame);
      expect(state.vss, equals(0.0));
    });

    test('parses VSS correctly when raw >= 893', () {
      // vss = 228480 / 1000 = 228.48 km/h
      final frame = _buildS300Frame(vss: 1000);
      final state = parseS300(frame);
      expect(state.vss, closeTo(228.48, 0.01));
    });

    test('parses MAP as raw/10 kPa', () {
      // mapRaw = 1148 -> 114.8 kPa
      final frame = _buildS300Frame(mapRaw: 1148);
      final state = parseS300(frame);
      expect(state.map, closeTo(114.8, 0.01));
    });

    test('parses TPS = 0 when raw = 0', () {
      final frame = _buildS300Frame(tps: 0);
      final state = parseS300(frame);
      expect(state.tps, equals(0.0));
    });

    test('parses TPS = 100 when raw = 255', () {
      final frame = _buildS300Frame(tps: 255);
      final state = parseS300(frame);
      expect(state.tps, equals(100.0));
    });

    test('parses TPS correctly when raw >= 25', () {
      // tps raw=127 -> 127*100/255 ≈ 49.8% (confirmed against live capture)
      final frame = _buildS300Frame(tps: 127);
      final state = parseS300(frame);
      expect(state.tps, closeTo(49.8, 0.1));
    });

    test('parses Gear from decimal offset 27', () {
      final frame = _buildS300Frame(gear: 5);
      final state = parseS300(frame);
      expect(state.gear, equals(5));
    });

    test('parses ECT using temp lookup table', () {
      // Confirmed via live capture: raw=0xD2(210) matched the reference
      // tool's 28.4°F exactly at the same instant (RPM cross-checked).
      // ect raw = 0xD2 = 210 → tempXlt[210]=38 → 38-40=-2°C
      final frame = _buildS300Frame(ect: 0xD2);
      final state = parseS300(frame);
      expect(state.ect, equals((tempXlt[0xD2] - 40).toDouble()));
    });

    test('parses IAT using temp lookup table', () {
      // Confirmed via the same live capture: raw=0xCA(202) was within
      // ~1.3°F of the reference tool's 36.1°F reading.
      // iat raw = 0xCA = 202 → tempXlt[202]=43 → 43-40=3°C
      final frame = _buildS300Frame(iat: 0xCA);
      final state = parseS300(frame);
      expect(state.iat, equals((tempXlt[0xCA] - 40).toDouble()));
    });

    test('parses BAT = raw * 26 / 270', () {
      // bat raw = 135 → 135*26/270 = 13.0 V
      final frame = _buildS300Frame(bat: 135);
      final state = parseS300(frame);
      expect(state.bat, closeTo(13.0, 0.01));
    });

    test('IGN decode: (raw + 120) / 2', () {
      // ign raw = 164 -> (164 + 120) / 2 = 142.0
      final frame = _buildS300Frame(ign: 164);
      final state = parseS300(frame);
      expect(state.ign, equals(142.0));
    });

    test('MIL flag set from SW2 bit5', () {
      final frame = _buildS300Frame(sw2: 0x20); // bit5 set
      final state = parseS300(frame);
      expect(state.mil, isTrue);
    });

    test('fuel pump flag is active-low: set when SW2 bit2 is CLEAR', () {
      // SW2 bit 2 is the "Fuel" line in the reference tool's own channel
      // list — confirmed live to be the fuel PUMP relay status, not fuel
      // cut, but also confirmed live to be active-low: an extended session
      // held RPM above the ~300 threshold where the pump should be on, and
      // this bit read 0 for the entire session. Separately confirmed the
      // app showed "on" below ~200 rpm and "off" above it — exactly
      // inverted from a naive `!= 0` read, hence bit CLEAR = pump on.
      final frame = _buildS300Frame(sw2: 0x38); // bit2 clear, other bits set
      final state = parseS300(frame);
      expect(state.fuelPump, isTrue);
    });

    test('fuel pump flag clear (pump off) when SW2 bit2 is set', () {
      final frame = _buildS300Frame(sw2: 0x04); // bit2 set
      final state = parseS300(frame);
      expect(state.fuelPump, isFalse);
    });

    test('knock flag set when krtrd > 0', () {
      final frame = _buildS300Frame(krtrd: 5);
      final state = parseS300(frame);
      expect(state.knock, isTrue);
    });

    test('knock flag clear when krtrd = 0', () {
      final frame = _buildS300Frame(krtrd: 0);
      final state = parseS300(frame);
      expect(state.knock, isFalse);
    });

    test('throws on wrong frame length', () {
      expect(
        () => parseS300(Uint8List(64)),
        throwsArgumentError,
      );
    });

    test('throws on bad checksum', () {
      final frame = _buildS300Frame(rpm: 1000);
      frame[127] = 0x00; // corrupt checksum
      expect(() => parseS300(frame), throwsArgumentError);
    });

    test('can parse bad checksum frame when validation is disabled', () {
      final frame = _buildS300Frame(rpm: 1000);
      frame[127] = 0x00; // corrupt checksum
      final state = parseS300(frame, validateChecksum: false);
      expect(state.rpm, equals(1000.0));
    });

    test('decodes RPM=0 for a frame matching the fixed event-frame template', () {
      // parseS300 itself doesn't special-case this template — it just reads
      // the normal offsets, which land on the template's fixed bytes.
      // Holding the last known-good value across this frame is the caller's
      // job (sensor_provider.dart), driven by isS300TemplateFrame below.
      final frame = _templateFrame();
      final state = parseS300(frame);
      expect(state.rpm, equals(0.0));
    });

    test('isS300TemplateFrame detects the fixed event-frame byte pattern', () {
      // Verified via live A/B capture: this exact bytes-0-16 pattern shows
      // up whenever SW2 (byte 18, outside this span) reports fuel cut
      // active, corroborated independently by the same frame's INJ pulse
      // width reading 0 and TPS reading a closed-throttle value.
      expect(isS300TemplateFrame(_templateFrame()), isTrue);
    });

    test('isS300TemplateFrame is false for a normal live-reading frame', () {
      final frame = _buildS300Frame(rpm: 3000, tps: 127);
      expect(isS300TemplateFrame(frame), isFalse);
    });
  });
}

/// Builds a 128-byte frame stamped with the S300's fixed event-frame
/// template in bytes 0-16, with a valid NEG8 checksum.
Uint8List _templateFrame() {
  final frame = Uint8List(128);
  final prefix = [
    0x1B,
    0x00,
    0x14,
    0x00,
    0x00,
    0xFF,
    0xFF,
    0xF2,
    0x03,
    0x18,
    0x00,
    0x00,
    0x10,
    0x00,
    0x00,
    0x00,
    0xC4,
  ];
  for (var i = 0; i < prefix.length; i++) {
    frame[i] = prefix[i];
  }
  frame[127] = calculateNeg8(frame.sublist(0, 127));
  return frame;
}